APRS Track Direct

My position About ☰

reset

BM6HIP-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM6HIP-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1732291585	21.2 C	18 p	80 p	3110 p
1732290385	21.8 C	19 p	118 p	3116 p
1732289184	21.7 C	43 p	167 p	3121 p
1732287984	21.9 C	56 p	185 p	3096 p
1732286784	21.7 C	68 p	190 p	3065 p
1732285584	21.9 C	61 p	159 p	3022 p
1732284384	21.8 C	61 p	142 p	2986 p
1732283184	21.8 C	37 p	103 p	2949 p
1732281985	21.3 C	44 p	87 p	2934 p
1732280785	21.6 C	22 p	59 p	2909 p
1732279584	21.8 C	21 p	54 p	2914 p
1732278384	22 C	16 p	53 p	2919 p
1732277184	21.3 C	17 p	70 p	2929 p
1732275984	21.3 C	20 p	129 p	2956 p
1732274785	22 C	33 p	161 p	2976 p
1732273585	21.8 C	76 p	171 p	2966 p
1732272385	22.5 C	52 p	138 p	2937 p
1732271185	22 C	43 p	120 p	2921 p
1732269984	22.4 C	43 p	147 p	2915 p
1732268784	22.5 C	34 p	162 p	2898 p
1732267584	22.5 C	70 p	197 p	2893 p
1732266384	22.3 C	58 p	232 p	2857 p
1732265184	22.2 C	69 p	282 p	2942 p
1732263984	22.2 C	105 p	271 p	2994 p
1732262784	21.7 C	108 p	223 p	2970 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)