APRS Track Direct

My position About ☰

reset

YB2DX Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YB2DX. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1732295059	7 Pkt	-74 dBm	13 V
1732294735	5 Pkt	-73 dBm	13 V
1732294411	7 Pkt	-74 dBm	13 V
1732294086	5 Pkt	-73 dBm	13 V
1732293762	7 Pkt	-74 dBm	13 V
1732293438	7 Pkt	-73 dBm	13 V
1732293115	4 Pkt	-74 dBm	13 V
1732292791	7 Pkt	-74 dBm	12.98 V
1732292467	7 Pkt	-73 dBm	13 V
1732292142	8 Pkt	-74 dBm	12.98 V
1732291819	0 Pkt	-74 dBm	13 V
1732291495	7 Pkt	-74 dBm	12.98 V
1732291170	5 Pkt	-74 dBm	13 V
1732290847	5 Pkt	-73 dBm	13 V
1732290523	6 Pkt	-73 dBm	13 V
1732290198	9 Pkt	-73 dBm	13 V
1732289875	9 Pkt	-73 dBm	12.98 V
1732289551	7 Pkt	-76 dBm	12.98 V
1732289227	7 Pkt	-74 dBm	12.98 V
1732288903	8 Pkt	-74 dBm	13 V
1732288579	10 Pkt	-74 dBm	13 V
1732288255	6 Pkt	-75 dBm	12.98 V
1732287931	7 Pkt	-74 dBm	13 V
1732287607	0 Pkt	-74 dBm	12.98 V
1732287220	5 Pkt	-76 dBm	12.98 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)