APRS Track Direct

My position About ☰

reset

SR9NIS Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9NIS. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*	Vbatt*
1790640385	7 Pkt	2 Pkt	0 Pkt	13.48 V
1790639747	12 Pkt	5 Pkt	0 Pkt	13.48 V
1790639118	11 Pkt	2 Pkt	0 Pkt	13.5 V
1790638479	17 Pkt	4 Pkt	0 Pkt	13.46 V
1790637203	12 Pkt	7 Pkt	0 Pkt	13.48 V
1790636569	20 Pkt	4 Pkt	0 Pkt	13.54 V
1790635931	13 Pkt	4 Pkt	1 Pkt	13.48 V
1790634653	10 Pkt	4 Pkt	0 Pkt	13.5 V
1790633377	8 Pkt	4 Pkt	0 Pkt	13.48 V
1790632739	11 Pkt	2 Pkt	0 Pkt	13.5 V
1790631472	15 Pkt	4 Pkt	0 Pkt	13.5 V
1790630838	13 Pkt	2 Pkt	0 Pkt	13.46 V
1790629558	17 Pkt	2 Pkt	0 Pkt	13.46 V
1790628920	19 Pkt	4 Pkt	0 Pkt	13.48 V
1790628281	22 Pkt	5 Pkt	0 Pkt	13.5 V
1790627651	16 Pkt	2 Pkt	0 Pkt	13.46 V
1790626370	18 Pkt	2 Pkt	0 Pkt	13.5 V
1790625732	13 Pkt	4 Pkt	0 Pkt	13.48 V
1790625105	15 Pkt	4 Pkt	0 Pkt	13.5 V
1790624465	18 Pkt	3 Pkt	0 Pkt	13.5 V
1790623826	19 Pkt	4 Pkt	0 Pkt	13.46 V
1790623188	19 Pkt	4 Pkt	0 Pkt	13.48 V
1790621914	20 Pkt	13 Pkt	0 Pkt	13.5 V
1790620642	26 Pkt	5 Pkt	0 Pkt	13.48 V
1790620003	35 Pkt	4 Pkt	0 Pkt	13.48 V

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)