This is the latest recevied telemetry packets stored in our database for station/object INDIAN. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Rx1h* | Rx10m* | Eff1h* | Temp* | Vin* |
|---|---|---|---|---|---|
| 1745032575 | 590 Pkt | 102 Pkt | 72 Pcnt | 43 F | 12.75 Volt |
| 1745032275 | 590 Pkt | 93 Pkt | 71 Pcnt | 43 F | 12.75 Volt |
| 1745031975 | 580 Pkt | 100 Pkt | 71 Pcnt | 43 F | 12.75 Volt |
| 1745031675 | 590 Pkt | 79 Pkt | 72 Pcnt | 43 F | 12.75 Volt |
| 1745031375 | 590 Pkt | 78 Pkt | 73 Pcnt | 43 F | 12.75 Volt |
| 1745031075 | 600 Pkt | 92 Pkt | 74 Pcnt | 43 F | 12.75 Volt |
| 1745030775 | 600 Pkt | 87 Pkt | 76 Pcnt | 43 F | 12.75 Volt |
| 1745030475 | 610 Pkt | 96 Pkt | 76 Pcnt | 43 F | 12.75 Volt |
| 1745030175 | 600 Pkt | 103 Pkt | 76 Pcnt | 43 F | 12.75 Volt |
| 1745029875 | 590 Pkt | 96 Pkt | 76 Pcnt | 43 F | 12.83 Volt |
| 1745029575 | 590 Pkt | 92 Pkt | 75 Pcnt | 43 F | 12.83 Volt |
| 1745029276 | 570 Pkt | 98 Pkt | 75 Pcnt | 43 F | 12.83 Volt |
| 1745028675 | 570 Pkt | 86 Pkt | 76 Pcnt | 43 F | 12.83 Volt |
*Used Equation Coefficients:
Rx1h: 0, 10, 0
Rx10m: 0, 1, 0
Eff1h: 0, 1, 0
Temp: 0, 0.9, -83
Vin: 0, 0.075, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)