APRS Track Direct

My position About ☰

reset

K3TOW-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object K3TOW-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Vin*	Rx1h*	Eff1h*	Temp*
1790651348	220 Volt	15 Pkt	93 Pcnt	255 Deg
1790650447	222 Volt	15 Pkt	92 Pcnt	255 Deg
1790649545	220 Volt	14 Pkt	90 Pcnt	255 Deg
1790646847	220 Volt	15 Pkt	90 Pcnt	255 Deg
1790645946	221 Volt	15 Pkt	93 Pcnt	255 Deg
1790644148	221 Volt	15 Pkt	96 Pcnt	255 Deg
1790642348	219 Volt	15 Pkt	99 Pcnt	255 Deg
1790642346	219 Volt	15 Pkt	99 Pcnt	255 Deg
1790640548	219 Volt	14 Pkt	99 Pcnt	255 Deg
1790638746	217 Volt	15 Pkt	98 Pcnt	255 Deg
1790637848	217 Volt	16 Pkt	97 Pcnt	255 Deg
1790635148	218 Volt	18 Pkt	93 Pcnt	255 Deg
1790635146	218 Volt	18 Pkt	93 Pcnt	255 Deg
1790634248	220 Volt	17 Pkt	93 Pcnt	255 Deg
1790633348	219 Volt	15 Pkt	89 Pcnt	255 Deg
1790632449	217 Volt	15 Pkt	88 Pcnt	255 Deg
1790631548	217 Volt	17 Pkt	87 Pcnt	255 Deg
1790631546	217 Volt	17 Pkt	87 Pcnt	255 Deg
1790630648	218 Volt	17 Pkt	85 Pcnt	255 Deg
1790627949	219 Volt	21 Pkt	91 Pcnt	255 Deg
1790627947	219 Volt	21 Pkt	91 Pcnt	255 Deg
1790627049	219 Volt	24 Pkt	93 Pcnt	255 Deg
1790624349	220 Volt	19 Pkt	90 Pcnt	255 Deg
1790624347	220 Volt	19 Pkt	90 Pcnt	255 Deg
1790621649	220 Volt	15 Pkt	98 Pcnt	255 Deg

*Used Equation Coefficients:

Vin: 0, 1, 0

Rx1h: 0, 1, 0

Dg1h: 0, 1, 0

Eff1h: 0, 1, 0

Temp: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)