APRS Track Direct

My position About ☰

reset

YD0BSK-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YD0BSK-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RxTraffic*	RSSI*	Voltage*
1758232302	0 Pkt	-39 dBm	12.1 V
1758231378	0 Pkt	-42 dBm	12.1 V
1758230455	0 Pkt	-41 dBm	12.12 V
1758229531	0 Pkt	-44 dBm	12.1 V
1758228607	0 Pkt	-44 dBm	12.1 V
1758227684	0 Pkt	-47 dBm	12.1 V
1758226760	0 Pkt	-45 dBm	12.12 V
1758225836	17 Pkt	-44 dBm	12.1 V
1758224911	20 Pkt	-44 dBm	12.1 V
1758223986	21 Pkt	-44 dBm	12.12 V
1758223060	19 Pkt	-44 dBm	12.1 V
1758222136	12 Pkt	-45 dBm	12.1 V
1758221210	26 Pkt	-45 dBm	12.1 V
1758219724	0 Pkt	-38 dBm	12.1 V
1758218800	0 Pkt	-49 dBm	12.1 V
1758217877	0 Pkt	-55 dBm	12.1 V
1758216029	0 Pkt	-47 dBm	12.1 V
1758215105	0 Pkt	-60 dBm	12.1 V
1758214181	0 Pkt	-37 dBm	12.1 V
1758213257	0 Pkt	-37 dBm	12.1 V
1758212333	0 Pkt	-35 dBm	12.1 V
1758211409	0 Pkt	-59 dBm	12.1 V
1758210485	0 Pkt	-60 dBm	12.1 V
1758209561	0 Pkt	-56 dBm	12.1 V
1758208638	0 Pkt	-56 dBm	12.1 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)