APRS Track Direct

My position About ☰

reset

IK2ILW Telemetry

This is the latest recevied telemetry packets stored in our database for station/object IK2ILW. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10m*	Rx1h*	Eff1h*
1753699040	19 Pkt	100 Pkt	71 Pcnt
1753698740	18 Pkt	100 Pkt	71 Pcnt
1753698440	16 Pkt	100 Pkt	68 Pcnt
1753698140	15 Pkt	100 Pkt	67 Pcnt
1753697839	14 Pkt	100 Pkt	67 Pcnt
1753697539	18 Pkt	100 Pkt	67 Pcnt
1753697239	23 Pkt	100 Pkt	67 Pcnt
1753696938	20 Pkt	100 Pkt	66 Pcnt
1753696638	18 Pkt	90 Pkt	65 Pcnt
1753696338	15 Pkt	90 Pkt	62 Pcnt
1753696038	16 Pkt	90 Pkt	63 Pcnt
1753695737	20 Pkt	90 Pkt	62 Pcnt
1753695437	19 Pkt	80 Pkt	60 Pcnt
1753695137	10 Pkt	90 Pkt	61 Pcnt
1753694836	13 Pkt	90 Pkt	63 Pcnt
1753694536	19 Pkt	100 Pkt	65 Pcnt
1753694236	19 Pkt	100 Pkt	66 Pcnt
1753693936	18 Pkt	100 Pkt	67 Pcnt
1753693635	14 Pkt	110 Pkt	68 Pcnt
1753693335	10 Pkt	130 Pkt	73 Pcnt
1753693035	14 Pkt	140 Pkt	76 Pcnt
1753692734	15 Pkt	160 Pkt	80 Pcnt
1753692434	10 Pkt	160 Pkt	80 Pcnt
1753692134	19 Pkt	160 Pkt	82 Pcnt
1753691834	25 Pkt	160 Pkt	83 Pcnt

*Used Equation Coefficients:

Rx10m: 0, 1, 0

Rx1h: 0, 10, 0

Dg10m: 0, 1, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)