APRS Track Direct

My position About ☰

reset

YM3KC-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YM3KC-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	RxTraffic*	RSSI*	Voltage*
1732265615	25 Pkt	31 dBm	12.26 V
1732264772	20 Pkt	31 dBm	12.26 V
1732263930	51 Pkt	31 dBm	12.26 V
1732263059	44 Pkt	31 dBm	12.26 V
1732262199	25 Pkt	31 dBm	12.26 V
1732261359	30 Pkt	31 dBm	12.26 V
1732260513	24 Pkt	31 dBm	12.26 V
1732259672	29 Pkt	31 dBm	12.26 V
1732258823	32 Pkt	31 dBm	12.3 V
1732257972	19 Pkt	31 dBm	12.3 V
1732257135	25 Pkt	31 dBm	12.3 V
1732256288	26 Pkt	31 dBm	12.26 V
1732255444	36 Pkt	31 dBm	12.26 V
1732254589	33 Pkt	31 dBm	12.26 V
1732253737	58 Pkt	31 dBm	12.26 V
1732252861	48 Pkt	31 dBm	12.26 V
1732252001	43 Pkt	31 dBm	12.3 V
1732251144	28 Pkt	31 dBm	12.26 V
1732250303	25 Pkt	31 dBm	12.3 V
1732249459	31 Pkt	31 dBm	12.26 V
1732248610	25 Pkt	31 dBm	12.3 V
1732247768	25 Pkt	31 dBm	12.26 V
1732246927	47 Pkt	31 dBm	12.26 V
1732246067	44 Pkt	31 dBm	12.26 V
1732245210	55 Pkt	31 dBm	12.26 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)