APRS Track Direct

My position About ☰

reset

9M2ARO-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 9M2ARO-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	RxTraffic*	RSSI*	Voltage*
1790646115	2 Pkt	-31 dBm	12.47 V
1790644290	2 Pkt	-32 dBm	12.49 V
1790642464	2 Pkt	-33 dBm	12.49 V
1790640638	2 Pkt	-32 dBm	12.49 V
1790638812	2 Pkt	-31 dBm	12.47 V
1790636987	2 Pkt	-31 dBm	12.49 V
1790635161	2 Pkt	-31 dBm	12.49 V
1790633334	2 Pkt	-33 dBm	12.49 V
1790631508	2 Pkt	-32 dBm	12.49 V
1790629682	2 Pkt	-32 dBm	12.49 V
1790627857	2 Pkt	-31 dBm	12.49 V
1790626031	2 Pkt	-32 dBm	12.49 V
1790624205	2 Pkt	-32 dBm	12.49 V
1790622379	2 Pkt	-33 dBm	12.47 V
1790620553	2 Pkt	-34 dBm	12.51 V
1790618727	2 Pkt	-32 dBm	12.49 V
1790616902	2 Pkt	-33 dBm	12.49 V
1790615076	2 Pkt	-31 dBm	12.49 V
1790613251	2 Pkt	-34 dBm	12.49 V
1790611424	2 Pkt	-32 dBm	12.49 V
1790609598	3 Pkt	-31 dBm	12.51 V
1790607772	2 Pkt	-32 dBm	12.51 V
1790605947	3 Pkt	-33 dBm	12.49 V
1790604120	2 Pkt	-32 dBm	12.51 V
1790602296	2 Pkt	-31 dBm	12.51 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)