APRS Track Direct

My position About ☰

reset

SP8EBC-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP8EBC-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Tx10min*	Vbatt*	Tempre*
1749328944	6 Pkt	12.64 V	17 DegC
1749328340	7 Pkt	12.66 V	17 DegC
1749327741	6 Pkt	12.68 V	17 DegC
1749327137	6 Pkt	12.68 V	17 DegC
1749326542	6 Pkt	12.68 V	17 DegC
1749325935	6 Pkt	12.68 V	17.5 DegC
1749325335	6 Pkt	12.68 V	17.5 DegC
1749324731	6 Pkt	12.68 V	17.5 DegC
1749324132	11 Pkt	12.68 V	17.5 DegC
1749323529	6 Pkt	12.7 V	18 DegC
1749322917	6 Pkt	12.68 V	18 DegC
1749322312	6 Pkt	12.7 V	18 DegC
1749321714	6 Pkt	12.7 V	18 DegC
1749321110	6 Pkt	12.7 V	18.5 DegC
1749320510	7 Pkt	12.72 V	18.5 DegC
1749319907	6 Pkt	12.68 V	18.5 DegC
1749319308	6 Pkt	12.72 V	18.5 DegC
1749318704	6 Pkt	12.72 V	18.5 DegC
1749318105	6 Pkt	12.72 V	18.5 DegC
1749317501	6 Pkt	12.7 V	18.5 DegC
1749316902	6 Pkt	12.72 V	19 DegC
1749316299	6 Pkt	12.72 V	19 DegC
1749315699	6 Pkt	12.72 V	19 DegC
1749315096	6 Pkt	12.74 V	19.5 DegC
1749314497	11 Pkt	12.7 V	20 DegC

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)