APRS Track Direct

My position About ☰

reset

YD3AWO-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YD3AWO-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	RSSI*	VBAT*	SOLAR*	RADIO*
1790661210	-10 dbm	1391 V	1382 V	1363 V
1790660910	-10 dbm	1389 V	1395 V	1360 V
1790660611	-10 dbm	1384 V	1376 V	1352 V
1790660310	-10 dbm	1382 V	1376 V	1356 V
1790660010	-10 dbm	1389 V	1380 V	1348 V
1790659711	-10 dbm	1389 V	1384 V	1363 V
1790659410	-10 dbm	1374 V	1376 V	1354 V
1790659110	-10 dbm	1382 V	1376 V	1352 V
1790658811	-10 dbm	1391 V	1384 V	1363 V
1790658510	-10 dbm	1391 V	1384 V	1363 V
1790657911	-10 dbm	1391 V	1384 V	1360 V
1790657614	-10 dbm	1391 V	1382 V	1363 V
1790656710	-10 dbm	1382 V	1372 V	1348 V
1790656110	-10 dbm	1391 V	1395 V	1352 V
1790655811	-10 dbm	1382 V	1382 V	1344 V
1790655510	-10 dbm	1391 V	1399 V	1363 V
1790655210	-10 dbm	1395 V	1384 V	1356 V
1790654910	-10 dbm	1389 V	1380 V	1363 V
1790654610	-10 dbm	1391 V	1393 V	1358 V
1790653710	-10 dbm	1395 V	1384 V	1363 V
1790653410	-10 dbm	1382 V	1376 V	1348 V
1790653110	-10 dbm	1391 V	1382 V	1367 V
1790652809	-10 dbm	1389 V	1380 V	1358 V
1790652509	-10 dbm	1384 V	1391 V	1354 V
1790651909	-10 dbm	1389 V	1382 V	1363 V

*Used Equation Coefficients:

RSSI: 0, 1, 0

VBAT: 0, 1, 0

SOLAR: 0, 1, 0

RADIO: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)