APRS Track Direct

My position About ☰

reset

SP9MOA-3 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SP9MOA-3. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Vin*	Rx1h*	Tx1h*
1758214402	12.93 Volt	670 Pkt	50 Pkt
1758213200	13 Volt	640 Pkt	30 Pkt
1758212006	13 Volt	630 Pkt	20 Pkt
1758210800	13 Volt	590 Pkt	20 Pkt
1758209599	13.08 Volt	540 Pkt	20 Pkt
1758208416	13.75 Volt	510 Pkt	10 Pkt
1758207195	13.9 Volt	530 Pkt	30 Pkt
1758205993	13.83 Volt	540 Pkt	60 Pkt
1758204799	13.98 Volt	600 Pkt	80 Pkt
1758203594	13.6 Volt	590 Pkt	40 Pkt
1758202399	13.83 Volt	560 Pkt	10 Pkt
1758201192	14.13 Volt	510 Pkt	0 Pkt
1758199988	13.83 Volt	460 Pkt	0 Pkt
1758198787	13.83 Volt	410 Pkt	0 Pkt
1758197593	14.05 Volt	390 Pkt	0 Pkt
1758196386	13.83 Volt	390 Pkt	0 Pkt
1758195184	13.9 Volt	410 Pkt	0 Pkt
1758193995	14.05 Volt	390 Pkt	0 Pkt
1758192783	13.83 Volt	360 Pkt	0 Pkt
1758191584	13.9 Volt	370 Pkt	0 Pkt
1758190383	14.05 Volt	370 Pkt	0 Pkt
1758189177	13.83 Volt	430 Pkt	0 Pkt
1758187976	13.83 Volt	400 Pkt	0 Pkt
1758186780	13.98 Volt	390 Pkt	0 Pkt
1758185574	13.83 Volt	350 Pkt	0 Pkt

*Used Equation Coefficients:

Vin: 0, 0.075, -0.2

Rx1h: 0, 10, 0

Tx1h: 0, 10, 0

None: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)