APRS Track Direct

My position About ☰

reset

HAMLTN Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HAMLTN. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1786727789	14.25 Volt	290 Pkt	80 Pkt	66 Pcnt
1786727489	14.25 Volt	280 Pkt	80 Pkt	64 Pcnt
1786727189	14.25 Volt	290 Pkt	90 Pkt	64 Pcnt
1786726888	14.25 Volt	300 Pkt	90 Pkt	65 Pcnt
1786726588	13.88 Volt	290 Pkt	80 Pkt	66 Pcnt
1786726288	14.25 Volt	290 Pkt	80 Pkt	65 Pcnt
1786725987	14.25 Volt	310 Pkt	80 Pkt	67 Pcnt
1786725687	14.25 Volt	320 Pkt	80 Pkt	66 Pcnt
1786725387	14.25 Volt	320 Pkt	80 Pkt	67 Pcnt
1786725087	14.25 Volt	320 Pkt	80 Pkt	66 Pcnt
1786724786	14.25 Volt	320 Pkt	80 Pkt	66 Pcnt
1786724486	14.25 Volt	320 Pkt	80 Pkt	64 Pcnt
1786724188	14.25 Volt	330 Pkt	90 Pkt	64 Pcnt
1786723885	14.25 Volt	340 Pkt	90 Pkt	66 Pcnt
1786723585	14.25 Volt	340 Pkt	90 Pkt	65 Pcnt
1786723285	14.25 Volt	340 Pkt	90 Pkt	64 Pcnt
1786722985	14.25 Volt	350 Pkt	90 Pkt	64 Pcnt
1786722684	14.25 Volt	380 Pkt	100 Pkt	66 Pcnt
1786722384	14.25 Volt	380 Pkt	110 Pkt	66 Pcnt
1786722084	14.25 Volt	390 Pkt	110 Pkt	67 Pcnt
1786721783	14.25 Volt	400 Pkt	110 Pkt	67 Pcnt
1786721483	14.25 Volt	420 Pkt	110 Pkt	67 Pcnt
1786721183	13.88 Volt	440 Pkt	110 Pkt	66 Pcnt
1786720883	14.25 Volt	460 Pkt	110 Pkt	66 Pcnt
1786720582	14.25 Volt	470 Pkt	100 Pkt	65 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

TEMP1: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)