APRS Track Direct

My position About ☰

reset

HS4LWD-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS4LWD-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1786735559	0 Pkt	-48 dBm	12.14 V
1786734636	0 Pkt	-46 dBm	12.12 V
1786733713	0 Pkt	-45 dBm	12.12 V
1786732790	0 Pkt	-46 dBm	12.14 V
1786731867	0 Pkt	-49 dBm	12.14 V
1786730944	1 Pkt	-47 dBm	12.14 V
1786730021	0 Pkt	-49 dBm	12.14 V
1786729098	0 Pkt	-47 dBm	12.14 V
1786728175	0 Pkt	-48 dBm	12.14 V
1786727252	1 Pkt	-46 dBm	12.14 V
1786726329	0 Pkt	-46 dBm	12.12 V
1786725406	0 Pkt	-46 dBm	12.12 V
1786724483	0 Pkt	-48 dBm	12.14 V
1786723560	1 Pkt	-46 dBm	12.14 V
1786722637	1 Pkt	-51 dBm	12.14 V
1786721714	0 Pkt	-51 dBm	12.12 V
1786720791	0 Pkt	-47 dBm	12.12 V
1786719868	0 Pkt	-51 dBm	12.14 V
1786718945	0 Pkt	-46 dBm	12.14 V
1786718022	0 Pkt	-50 dBm	12.14 V
1786717100	2 Pkt	-47 dBm	12.12 V
1786716177	0 Pkt	-49 dBm	12.16 V
1786715254	0 Pkt	-47 dBm	12.14 V
1786714331	0 Pkt	-48 dBm	12.14 V
1786713408	0 Pkt	-44 dBm	12.14 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)