APRS Track Direct

My position About ☰

reset

YE1BPQ-13 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YE1BPQ-13. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1786878779	0 Pkt	-70 dBm	0.8 V
1786877857	0 Pkt	-70 dBm	2.34 V
1786876935	0 Pkt	-70 dBm	8.78 V
1786876013	0 Pkt	-70 dBm	13.21 V
1786875091	0 Pkt	-71 dBm	14.62 V
1786874170	0 Pkt	-71 dBm	11.48 V
1786873248	0 Pkt	-73 dBm	17.58 V
1786872325	0 Pkt	-71 dBm	19.34 V
1786871403	0 Pkt	-70 dBm	19.22 V
1786870481	0 Pkt	-73 dBm	19.26 V
1786869559	0 Pkt	-71 dBm	18.79 V
1786868637	1 Pkt	-72 dBm	19.24 V
1786867715	0 Pkt	-72 dBm	19.09 V
1786866793	0 Pkt	-70 dBm	19.81 V
1786865871	0 Pkt	-70 dBm	18.72 V
1786864949	0 Pkt	-69 dBm	19.75 V
1786864027	0 Pkt	-70 dBm	18.81 V
1786863105	0 Pkt	-71 dBm	20.14 V
1786862183	0 Pkt	-70 dBm	19.77 V
1786861261	0 Pkt	-69 dBm	20.49 V
1786860339	0 Pkt	-70 dBm	18.54 V
1786859417	4 Pkt	-69 dBm	18.54 V
1786858495	0 Pkt	-70 dBm	18.54 V
1786857573	2 Pkt	-70 dBm	18.27 V
1786856651	0 Pkt	-70 dBm	18.33 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)