APRS Track Direct

My position About ☰

reset

ED6YAE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED6YAE-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	DC*	RxP-1h*	Dg1h*	Eff1h*
1790631740	9.08 Volt	210 Pkt	130 Pkt	79 *100
1790631440	8.7 Volt	220 Pkt	140 Pkt	80 *100
1790631140	8.78 Volt	230 Pkt	140 Pkt	79 *100
1790630840	8.78 Volt	230 Pkt	140 Pkt	77 *100
1790630540	8.78 Volt	230 Pkt	140 Pkt	73 *100
1790630240	8.78 Volt	230 Pkt	140 Pkt	73 *100
1790629940	8.78 Volt	230 Pkt	130 Pkt	74 *100
1790629640	9 Volt	220 Pkt	130 Pkt	76 *100
1790629340	8.85 Volt	210 Pkt	120 Pkt	74 *100
1790629040	8.85 Volt	210 Pkt	120 Pkt	73 *100
1790628740	8.7 Volt	210 Pkt	120 Pkt	70 *100
1790628440	8.78 Volt	210 Pkt	120 Pkt	69 *100
1790628140	8.7 Volt	210 Pkt	120 Pkt	69 *100
1790627840	8.78 Volt	210 Pkt	120 Pkt	68 *100
1790627540	8.85 Volt	210 Pkt	120 Pkt	70 *100
1790627240	8.78 Volt	220 Pkt	130 Pkt	72 *100
1790626940	8.7 Volt	240 Pkt	140 Pkt	80 *100
1790626640	8.78 Volt	230 Pkt	140 Pkt	78 *100
1790626340	8.85 Volt	250 Pkt	150 Pkt	78 *100
1790626040	8.78 Volt	260 Pkt	160 Pkt	79 *100
1790625740	8.78 Volt	260 Pkt	160 Pkt	80 *100
1790625440	8.78 Volt	270 Pkt	160 Pkt	82 *100
1790625140	8.7 Volt	270 Pkt	160 Pkt	80 *100
1790624840	8.7 Volt	270 Pkt	160 Pkt	82 *100
1790624540	8.78 Volt	270 Pkt	160 Pkt	83 *100

*Used Equation Coefficients:

DC: 0, 0.075, 0

RxP-1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

DC-1: 0, 0.075, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)