APRS Track Direct

My position About ☰

reset

ED6YAE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object ED6YAE-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	DC*	RxP-1h*	Dg1h*	Eff1h*
1836274805	8.78 Volt	190 Pkt	140 Pkt	89 *100
1836274506	9 Volt	200 Pkt	140 Pkt	89 *100
1836274355	9.08 Volt	200 Pkt	140 Pkt	90 *100
1836274205	8.78 Volt	210 Pkt	150 Pkt	89 *100
1836273906	9.15 Volt	210 Pkt	150 Pkt	89 *100
1770129934	9.83 Volt	430 Pkt	310 Pkt	81 *100
1770129634	9.83 Volt	440 Pkt	310 Pkt	81 *100
1770129334	9.83 Volt	450 Pkt	310 Pkt	82 *100
1770129034	9.83 Volt	440 Pkt	310 Pkt	82 *100
1770128734	9.83 Volt	440 Pkt	310 Pkt	82 *100
1770128434	9.83 Volt	440 Pkt	310 Pkt	82 *100
1770128134	9.83 Volt	440 Pkt	310 Pkt	82 *100
1770127834	9.83 Volt	450 Pkt	320 Pkt	83 *100
1770127534	9.83 Volt	450 Pkt	320 Pkt	83 *100
1770127234	9.83 Volt	450 Pkt	320 Pkt	82 *100
1770126934	9.83 Volt	440 Pkt	310 Pkt	81 *100
1770126634	9.83 Volt	420 Pkt	300 Pkt	80 *100
1770126334	9.9 Volt	430 Pkt	300 Pkt	81 *100
1770126034	9.83 Volt	420 Pkt	300 Pkt	81 *100
1770125734	9.9 Volt	410 Pkt	290 Pkt	81 *100
1770125434	9.9 Volt	410 Pkt	290 Pkt	80 *100
1770125134	9.98 Volt	410 Pkt	290 Pkt	82 *100
1770124834	9.9 Volt	410 Pkt	280 Pkt	82 *100
1770124534	9.83 Volt	410 Pkt	280 Pkt	82 *100
1770124234	9.83 Volt	410 Pkt	280 Pkt	82 *100

*Used Equation Coefficients:

DC: 0, 0.075, 0

RxP-1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

DC-1: 0, 0.075, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)