APRS Track Direct

My position About ☰

reset

SR9WXM Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9WXM. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Tx10min*	Digi10min*	Visc10min*
1749329040	105 Pkt	6 Pkt	1 Pkt	1 Pkt
1749328440	104 Pkt	8 Pkt	2 Pkt	2 Pkt
1749327836	111 Pkt	9 Pkt	4 Pkt	2 Pkt
1749327235	110 Pkt	7 Pkt	2 Pkt	2 Pkt
1749326633	113 Pkt	6 Pkt	1 Pkt	3 Pkt
1749326033	110 Pkt	7 Pkt	2 Pkt	1 Pkt
1749325431	118 Pkt	7 Pkt	2 Pkt	2 Pkt
1749324831	129 Pkt	7 Pkt	2 Pkt	3 Pkt
1749324229	130 Pkt	13 Pkt	8 Pkt	4 Pkt
1749323628	108 Pkt	7 Pkt	2 Pkt	3 Pkt
1749323026	113 Pkt	7 Pkt	2 Pkt	1 Pkt
1749322426	147 Pkt	8 Pkt	3 Pkt	1 Pkt
1749321824	129 Pkt	11 Pkt	6 Pkt	1 Pkt
1749321224	120 Pkt	10 Pkt	4 Pkt	3 Pkt
1749320622	122 Pkt	9 Pkt	4 Pkt	4 Pkt
1749320022	98 Pkt	11 Pkt	3 Pkt	2 Pkt
1749319412	126 Pkt	7 Pkt	2 Pkt	1 Pkt
1749318812	137 Pkt	6 Pkt	1 Pkt	3 Pkt
1749318209	136 Pkt	6 Pkt	1 Pkt	3 Pkt
1749317609	119 Pkt	6 Pkt	1 Pkt	3 Pkt
1749317008	140 Pkt	10 Pkt	5 Pkt	3 Pkt
1749316408	121 Pkt	10 Pkt	5 Pkt	1 Pkt
1749315806	127 Pkt	9 Pkt	4 Pkt	3 Pkt
1749315206	140 Pkt	8 Pkt	3 Pkt	1 Pkt
1749314604	129 Pkt	7 Pkt	2 Pkt	0 Pkt

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Tx10min: 0, 1, 0

Digi10min: 0, 1, 0

Visc10min: 0, 1, 0

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)