APRS Track Direct

My position About ☰

reset

LD4AI Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LD4AI. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Rx1h*	Eff1h*	Temp*
1786727442	12.6 Volt	850 Pkt	65 Pcnt	22.5 C
1786727144	12.6 Volt	890 Pkt	66 Pcnt	22.5 C
1786727142	12.6 Volt	890 Pkt	66 Pcnt	22.5 C
1786726842	12.6 Volt	920 Pkt	67 Pcnt	22.5 C
1786726543	12.6 Volt	940 Pkt	68 Pcnt	22.5 C
1786726541	12.6 Volt	940 Pkt	68 Pcnt	22.5 C
1786726241	12.6 Volt	950 Pkt	69 Pcnt	22.5 C
1786725942	12.6 Volt	960 Pkt	70 Pcnt	22.5 C
1786725941	12.6 Volt	960 Pkt	70 Pcnt	22.5 C
1786725640	12.6 Volt	960 Pkt	70 Pcnt	22.5 C
1786725340	12.6 Volt	970 Pkt	70 Pcnt	22.5 C
1786725040	12.6 Volt	960 Pkt	70 Pcnt	22.5 C
1786724741	12.6 Volt	980 Pkt	71 Pcnt	22.5 C
1786724740	12.6 Volt	980 Pkt	71 Pcnt	22.5 C
1786724439	12.6 Volt	980 Pkt	71 Pcnt	22.5 C
1786724142	12.6 Volt	1010 Pkt	71 Pcnt	22.5 C
1786724139	12.6 Volt	1010 Pkt	71 Pcnt	22.5 C
1786723839	12.6 Volt	1030 Pkt	71 Pcnt	22.5 C
1786723538	12.6 Volt	1050 Pkt	72 Pcnt	22.5 C
1786723238	12.6 Volt	1070 Pkt	72 Pcnt	22.5 C
1786722938	12.6 Volt	1100 Pkt	72 Pcnt	22.5 C
1786722637	12.6 Volt	1120 Pkt	72 Pcnt	22.5 C
1786722337	12.6 Volt	1170 Pkt	72 Pcnt	22.5 C
1786722037	12.6 Volt	1230 Pkt	72 Pcnt	22.5 C
1786721737	12.6 Volt	1260 Pkt	72 Pcnt	22.5 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)