APRS Track Direct

My position About ☰

reset

TA3TX-14 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object TA3TX-14. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1770098785	62 Pkt	-47 dBm	21 V
1770098457	76 Pkt	-46 dBm	21 V
1770098126	67 Pkt	-47 dBm	21 V
1770097796	75 Pkt	-46 dBm	21 V
1770097464	59 Pkt	-46 dBm	21 V
1770097138	60 Pkt	-46 dBm	21 V
1770096810	78 Pkt	-46 dBm	21 V
1770096481	59 Pkt	-46 dBm	21 V
1770096153	69 Pkt	-46 dBm	21 V
1770095824	12 Pkt	-47 dBm	21 V
1770095570	53 Pkt	-47 dBm	21 V
1770095241	51 Pkt	-46 dBm	21 V
1770094914	61 Pkt	-47 dBm	21 V
1770094585	50 Pkt	-47 dBm	21 V
1770094256	52 Pkt	-46 dBm	21 V
1770093929	45 Pkt	-47 dBm	21 V
1770093603	55 Pkt	-48 dBm	21 V
1770093275	59 Pkt	-45 dBm	21 V
1770092947	54 Pkt	-46 dBm	21 V
1770092619	49 Pkt	-47 dBm	21 V
1770092292	11 Pkt	-46 dBm	21 V
1770092029	57 Pkt	-46 dBm	21 V
1770091699	50 Pkt	-47 dBm	21 V
1770091373	66 Pkt	-47 dBm	21 V
1770091043	50 Pkt	-47 dBm	21 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)