APRS Track Direct

My position About ☰

reset

HB9FEF-8 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HB9FEF-8. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Vin*	Temp 1*	Temp 2*
1790668350	13.28 Volt	25.5 C	25.5 C
1790664750	13.13 Volt	22.5 C	22.5 C
1790662949	14.7 Volt	18 C	18 C
1790661150	12.98 Volt	14 C	14 C
1790659350	13.13 Volt	14.5 C	14.5 C
1790657550	13.2 Volt	13.5 C	13.5 C
1790655750	12.98 Volt	13 C	13 C
1790653950	12.98 Volt	13 C	13 C
1790652150	12.98 Volt	13.5 C	13.5 C
1790650350	12.98 Volt	14 C	14 C
1790648550	12.98 Volt	14 C	14 C
1790646750	12.98 Volt	14.5 C	14.5 C
1790644950	13.05 Volt	14.5 C	14.5 C
1790643150	13.05 Volt	15 C	15 C
1790641350	13.05 Volt	15.5 C	15.5 C
1790639550	13.05 Volt	16 C	16 C
1790637750	13.05 Volt	16.5 C	16.5 C
1790635950	13.05 Volt	17 C	17 C
1790634150	13.13 Volt	18 C	18 C
1790632350	13.13 Volt	18.5 C	18.5 C
1790630550	13.13 Volt	19.5 C	19.5 C
1790628750	13.13 Volt	20.5 C	20.5 C
1790626950	13.13 Volt	21.5 C	21.5 C
1790625150	13.2 Volt	23 C	23 C
1790623350	13.2 Volt	24 C	24 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Temp 1: 0, 0.5, -64

Temp 2: 0, 0.5, -64

U: 0, 0.1, 0

I: 0, 19.5, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)