APRS Track Direct

My position About ☰

reset

HS5TQA-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS5TQA-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	VBAT*	IBAT*	TEMP*
1779782846	13.74 V	-64 mA	31.52 °C
1779781046	13.74 V	-68 mA	32.59 °C
1779779247	14.09 V	-1 mA	32.64 °C
1779777452	14.09 V	-1 mA	32.89 °C
1779775658	14.09 V	-1 mA	32.67 °C
1779775197	14.1 V	-1 mA	33.27 °C
1779774453	14.09 V	-1 mA	32.82 °C
1779773309	14.09 V	-1 mA	32.73 °C
1779772053	13.73 V	-312 mA	31.47 °C
1779771447	13.77 V	-658 mA	31.45 °C
1779770874	14.09 V	-1 mA	31.2 °C
1779769510	13.73 V	-342 mA	30.94 °C
1779769172	14.09 V	-1 mA	30.23 °C
1779767372	14.09 V	-1 mA	31.37 °C
1779765572	14.09 V	-1 mA	31.2 °C
1779764246	14.09 V	-1 mA	31.14 °C
1779762446	14.09 V	-1 mA	30.06 °C
1779760646	13.41 V	-189 mA	29.49 °C
1779760517	13.42 V	-231 mA	29.4 °C
1779758717	13.41 V	-414 mA	28.5 °C
1779758560	13.39 V	-377 mA	28.34 °C
1779756760	13.3 V	-287 mA	25.88 °C
1779754960	13.18 V	-49 mA	25.12 °C
1779753160	13.15 V	8 mA	24.32 °C
1779751360	13.14 V	45 mA	23.06 °C

*Used Equation Coefficients:

VBAT: 0, 0.01, 0

IBAT: 0, 1, -2000

SOLAR: 0, 0.01, 0

SUN: 0, 1, 0

TEMP: 0, 0.01, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)