APRS Track Direct

My position About ☰

reset

DB0EMS-5 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DB0EMS-5. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	U1*	U2*	Temp*
1790646661	13.2 Volt	13.6 Volt	23.5 C
1790646360	13.2 Volt	13.6 Volt	23 C
1790646060	13.2 Volt	13.6 Volt	23 C
1790645760	13.2 Volt	13.6 Volt	23 C
1790645459	13.2 Volt	13.6 Volt	23 C
1790645159	13.2 Volt	13.6 Volt	22.5 C
1790644859	13.2 Volt	13.6 Volt	21.5 C
1790644558	13.2 Volt	13.6 Volt	22.5 C
1790644258	13.2 Volt	13.6 Volt	23.5 C
1790643958	13.2 Volt	13.6 Volt	23.5 C
1790643658	13.2 Volt	13.6 Volt	23.5 C
1790643357	13.2 Volt	13.6 Volt	23 C
1790643057	13.2 Volt	13.6 Volt	23 C
1790642757	13.2 Volt	13.6 Volt	23 C
1790642457	13.2 Volt	13.6 Volt	23 C
1790642156	13.2 Volt	13.6 Volt	22.5 C
1790641856	13.2 Volt	13.6 Volt	21.5 C
1790641556	13.2 Volt	13.6 Volt	22.5 C
1790641255	13.2 Volt	13.6 Volt	23.5 C
1790640955	13.2 Volt	13.6 Volt	23.5 C
1790640655	13.2 Volt	13.6 Volt	23.5 C
1790640354	13.2 Volt	13.6 Volt	23 C
1790640054	13.2 Volt	13.6 Volt	23 C
1790639754	13.2 Volt	13.6 Volt	23 C
1790639454	13.2 Volt	13.6 Volt	22.5 C

*Used Equation Coefficients:

U1: 0, 0.1, 0

U2: 0, 0.1, 0

Temp: 0, 0.5, -64

Vin: 0, 0.079, 0

I2: 0, 19.5, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)