APRS Track Direct

My position About ☰

reset

DL7AD-15 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DL7AD-15. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Value1*	Value2*	Value3*	Value4*	Value5*
1786723780	4016	2511	68	1367	8059
1786723480	4008	2501	69	1369	8059
1786723181	4000	2518	68	1369	8059
1786722881	3988	2522	68	1369	8059
1786722580	3984	2522	69	1371	8060
1786722285	3976	2514	68	1370	8060
1786721981	3968	2503	68	1371	8060
1786721681	3960	2496	69	1371	8061
1786721380	3949	2485	69	1370	8061
1786721081	3941	2492	68	1369	8062
1786720780	3932	2481	70	1370	8062
1786720483	3925	2483	68	1368	8063
1786720180	3914	2471	69	1368	8063
1786719880	3907	2460	69	1367	8063
1786719580	3902	2461	69	1367	8064
1786719284	3893	2475	69	1367	8064
1786718980	3887	2482	69	1366	8066
1786718680	3878	2488	70	1366	8066
1786718382	3872	2474	68	1365	8066
1786718081	3864	2481	69	1365	8067
1786717780	3856	2459	69	1365	8068
1786717482	3848	2455	69	1364	8068
1786717180	3840	2451	69	1364	8069
1786716885	3832	2476	68	1363	8069
1786716581	3824	2478	68	1362	8069

*Used Equation Coefficients:

Value1: 0, 1, 0

Value2: 0, 1, 0

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)