This is the latest recevied telemetry packets stored in our database for station/object BRIVER. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | Rx1h* | Dg1h* | Eff1h* | Temp* | Vin* |
|---|---|---|---|---|---|
| 1792143058 | 100 Pkt | 10 Pkt | 40 Pcnt | 68.2 F | 13.45 Volt |
| 1792142758 | 100 Pkt | 10 Pkt | 41 Pcnt | 69.1 F | 13.45 Volt |
| 1792142458 | 100 Pkt | 10 Pkt | 41 Pcnt | 69.1 F | 13.45 Volt |
| 1792142158 | 90 Pkt | 10 Pkt | 40 Pcnt | 69.1 F | 13.38 Volt |
| 1792141858 | 100 Pkt | 10 Pkt | 41 Pcnt | 69.1 F | 13.45 Volt |
| 1792141558 | 100 Pkt | 10 Pkt | 45 Pcnt | 69.1 F | 13.45 Volt |
| 1792141258 | 110 Pkt | 10 Pkt | 47 Pcnt | 68.2 F | 13.45 Volt |
| 1792140958 | 110 Pkt | 10 Pkt | 46 Pcnt | 68.2 F | 13.45 Volt |
| 1792140659 | 110 Pkt | 10 Pkt | 49 Pcnt | 69.1 F | 13.45 Volt |
| 1792140658 | 110 Pkt | 10 Pkt | 49 Pcnt | 69.1 F | 13.45 Volt |
| 1792140358 | 120 Pkt | 10 Pkt | 50 Pcnt | 68.2 F | 13.45 Volt |
| 1792140058 | 120 Pkt | 10 Pkt | 52 Pcnt | 68.2 F | 13.38 Volt |
| 1792139759 | 130 Pkt | 20 Pkt | 54 Pcnt | 68.2 F | 13.45 Volt |
| 1792139758 | 130 Pkt | 20 Pkt | 54 Pcnt | 68.2 F | 13.45 Volt |
*Used Equation Coefficients:
Rx1h: 0, 10, 0
Dg1h: 0, 10, 0
Eff1h: 0, 1, 0
Temp: 0, 0.9, -83
Vin: 0, 0.075, -0.5
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)