APRS Track Direct

My position About ☰

reset

BM3DQG-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM3DQG-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	CPUTemp*	RxPkts/10m*	RxPkts/1h*	RxPkts/24h*
1744984882	56 C	32 p	105 p	2027 p
1744983683	56 C	25 p	74 p	1975 p
1744982482	56 C	8 p	73 p	1936 p
1744981282	57 C	12 p	134 p	1922 p
1744980083	56 C	17 p	184 p	1901 p
1744978883	56 C	41 p	219 p	1863 p
1744977683	56 C	30 p	263 p	1788 p
1744976482	56 C	32 p	293 p	1717 p
1744975282	56 C	63 p	315 p	1644 p
1744974082	56 C	49 p	245 p	1525 p
1744972882	57 C	52 p	188 p	1425 p
1744971682	57 C	22 p	147 p	1329 p
1744970482	57 C	23 p	141 p	1280 p
1744969282	56 C	22 p	143 p	1237 p
1744968082	57 C	29 p	124 p	1182 p
1744966882	57 C	18 p	123 p	1139 p
1744965682	57 C	20 p	113 p	1094 p
1744964481	57 C	25 p	109 p	1058 p
1744963282	57 C	19 p	105 p	1016 p
1744962081	57 C	19 p	109 p	981 p
1744960882	57 C	21 p	111 p	949 p
1744959682	57 C	19 p	119 p	911 p
1744958482	57 C	12 p	120 p	872 p
1744957282	57 C	23 p	135 p	838 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/10m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)