APRS Track Direct

My position About ☰

reset

BX2AHP-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX2AHP-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/10m*	RxPkts/1h*	RxPkts/24h*
1750145702	56 C	27 p	201 p	1120 p
1750144502	56 C	29 p	241 p	1062 p
1750143302	56 C	51 p	260 p	999 p
1750142102	56 C	49 p	243 p	919 p
1750140902	57 C	42 p	205 p	821 p
1750139702	56 C	35 p	177 p	739 p
1750138502	56 C	33 p	143 p	676 p
1750137302	56 C	27 p	117 p	616 p
1750136102	56 C	10 p	92 p	562 p
1750134902	56 C	18 p	100 p	533 p
1750133702	56 C	14 p	98 p	499 p
1750132502	56 C	22 p	104 p	470 p
1750131302	56 C	17 p	103 p	433 p
1750130102	56 C	18 p	99 p	401 p
1750128902	56 C	15 p	90 p	366 p
1750127702	56 C	16 p	79 p	330 p
1750126502	56 C	10 p	88 p	302 p
1750125301	56 C	11 p	88 p	276 p
1750124102	56 C	20 p	159 p	251 p
1750122902	56 C	7 p	176 p	214 p
1750121702	56 C	48 p	188 p	188 p
1750120501	56 C	27 p	92 p	92 p
1750119301	56 C	32 p	38 p	38 p
1750118104	56 C	26 p	97 p	2674 p
1750116904	56 C	11 p	113 p	2633 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/10m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)