APRS Track Direct

My position About ☰

reset

PU2PPB Telemetry

This is the latest recevied telemetry packets stored in our database for station/object PU2PPB. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TX Avg 30m*	RX Count 30m*	TX Count 30m*
1750165604	0.01 erlang	0 receptions	2 transmissions
1750163804	0.38 erlang	0 receptions	23 transmissions
1750162004	0.16 erlang	0 receptions	27 transmissions
1750160204	0.83 erlang	0 receptions	61 transmissions
1750158404	0.76 erlang	0 receptions	69 transmissions
1750156604	0.78 erlang	0 receptions	57 transmissions
1750154804	0.83 erlang	0 receptions	47 transmissions
1750153004	0.43 erlang	0 receptions	26 transmissions
1750151204	0.02 erlang	0 receptions	9 transmissions
1750149404	0.02 erlang	0 receptions	5 transmissions
1750147604	0.01 erlang	0 receptions	3 transmissions
1750145804	0.01 erlang	0 receptions	6 transmissions
1750144004	0.01 erlang	0 receptions	2 transmissions
1750142204	0.01 erlang	0 receptions	2 transmissions
1750140404	0.01 erlang	0 receptions	2 transmissions
1750138604	0.01 erlang	0 receptions	2 transmissions
1750136804	0.01 erlang	0 receptions	3 transmissions
1750135004	0.01 erlang	0 receptions	2 transmissions
1750133204	0.01 erlang	0 receptions	2 transmissions
1750131404	0.01 erlang	0 receptions	2 transmissions
1750129604	0.01 erlang	0 receptions	2 transmissions
1750127804	0.01 erlang	0 receptions	2 transmissions
1750126004	0.13 erlang	0 receptions	12 transmissions
1750124204	0.91 erlang	0 receptions	61 transmissions
1750122404	0.93 erlang	0 receptions	48 transmissions

*Used Equation Coefficients:

RX Avg 30m: 0, 0.001, 0

TX Avg 30m: 0, 0.001, 0

RX Count 30m: 0, 1, 0

TX Count 30m: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)