This is the latest recevied telemetry packets stored in our database for station/object OK1FWG-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).
Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).
| Time | TX* | RX* | Digi* | V_Bat* | V_Ext* |
|---|---|---|---|---|---|
| 1779786151 | 842 | 476 | 332 | 0 | 0 |
| 1779784348 | 841 | 476 | 332 | 0 | 0 |
| 1779780741 | 839 | 476 | 332 | 0 | 0 |
| 1779777135 | 837 | 476 | 332 | 0 | 0 |
| 1779775332 | 836 | 476 | 332 | 0 | 0 |
| 1779773529 | 835 | 463 | 332 | 0 | 0 |
| 1779769923 | 833 | 450 | 332 | 0 | 0 |
| 1779768120 | 832 | 450 | 332 | 0 | 0 |
| 1779766316 | 830 | 449 | 331 | 0 | 0 |
| 1779759104 | 820 | 443 | 325 | 0 | 0 |
| 1779755498 | 818 | 443 | 325 | 0 | 0 |
| 1779751893 | 816 | 443 | 325 | 0 | 0 |
| 1779750089 | 815 | 443 | 325 | 0 | 0 |
| 1779748286 | 814 | 443 | 325 | 0 | 0 |
| 1779744680 | 812 | 443 | 325 | 0 | 0 |
| 1779742878 | 811 | 443 | 325 | 0 | 0 |
| 1779741074 | 810 | 443 | 325 | 0 | 0 |
| 1779737468 | 808 | 443 | 325 | 0 | 0 |
| 1779735665 | 803 | 439 | 321 | 0 | 0 |
| 1779733862 | 794 | 431 | 313 | 0 | 0 |
| 1779730256 | 791 | 430 | 312 | 0 | 0 |
| 1779723044 | 787 | 430 | 312 | 0 | 0 |
| 1779719437 | 777 | 422 | 304 | 0 | 0 |
| 1779715832 | 775 | 422 | 304 | 0 | 0 |
| 1779714029 | 774 | 422 | 304 | 0 | 0 |
*Used Equation Coefficients:
TX: 0, 1, 0
RX: 0, 1, 0
Digi: 0, 1, 0
V_Bat: 0, 1, 0
V_Ext: 0, 1, 0
- The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
- Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value2 + b * value + c. - The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
- The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
- All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
- A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)