APRS Track Direct

☰

reset

DH8TOM-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object DH8TOM-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	RX10m*	RX1h*	Eff1h*	Temp*
1792261182	20 Pkt	260 Pkt	100 Pcnt	17.28 Grad
1792260882	19 Pkt	370 Pkt	100 Pcnt	17.28 Grad
1792260582	19 Pkt	380 Pkt	100 Pcnt	17.28 Grad
1792260282	19 Pkt	300 Pkt	100 Pcnt	17.28 Grad
1792259981	18 Pkt	390 Pkt	100 Pcnt	17.28 Grad
1792259681	18 Pkt	420 Pkt	100 Pcnt	17.28 Grad
1792259381	18 Pkt	320 Pkt	100 Pcnt	17.28 Grad
1792259080	17 Pkt	340 Pkt	100 Pcnt	17.28 Grad
1792258780	16 Pkt	340 Pkt	100 Pcnt	17.28 Grad
1792258480	16 Pkt	260 Pkt	100 Pcnt	17.28 Grad
1792258180	16 Pkt	310 Pkt	100 Pcnt	17.28 Grad
1792257879	16 Pkt	290 Pkt	100 Pcnt	17.28 Grad
1792257579	17 Pkt	190 Pkt	100 Pcnt	17.28 Grad
1792257279	17 Pkt	300 Pkt	100 Pcnt	17.28 Grad
1792256978	17 Pkt	320 Pkt	100 Pcnt	17.28 Grad
1792256678	18 Pkt	250 Pkt	100 Pcnt	17.28 Grad
1792256378	18 Pkt	340 Pkt	100 Pcnt	17.28 Grad
1792256078	18 Pkt	280 Pkt	99 Pcnt	17.28 Grad
1792255777	18 Pkt	180 Pkt	99 Pcnt	17.28 Grad
1792255477	19 Pkt	270 Pkt	99 Pcnt	17.28 Grad

*Used Equation Coefficients:

RX10m: 0, 1, 0

RX1h: 0, 10, 0

Eff1h: 0, 1, 0

Vin: 0, 0.101, 0

Temp: 0, 0.135, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)

Maintained by UW0WU-1, based on APRS Track Direct