APRS Track Direct

My position About ☰

reset

MB7UNE-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object MB7UNE-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Temp*	Vin*	Dg1h*	Eff1h*
1786731505	37.5 C	13.88 Volt	20 Pkt	90
1786730906	37.5 C	13.88 Volt	20 Pkt	88
1786730905	37.5 C	13.88 Volt	20 Pkt	88
1786730305	37.5 C	13.88 Volt	20 Pkt	87
1786729705	37.5 C	13.88 Volt	20 Pkt	89
1786729106	37.5 C	13.88 Volt	20 Pkt	89
1786729105	37.5 C	13.88 Volt	20 Pkt	89
1786728505	37.5 C	13.88 Volt	20 Pkt	89
1786727905	37.5 C	13.88 Volt	20 Pkt	91
1786727306	37.5 C	13.88 Volt	20 Pkt	90
1786727305	37.5 C	13.88 Volt	20 Pkt	90
1786726705	37.5 C	13.88 Volt	20 Pkt	92
1786726105	37.5 C	13.88 Volt	20 Pkt	90
1786725506	37.5 C	13.88 Volt	20 Pkt	92
1786725505	37.5 C	13.88 Volt	20 Pkt	92
1786724905	37.5 C	13.88 Volt	20 Pkt	92
1786724305	37.5 C	13.88 Volt	20 Pkt	90
1786723706	37.5 C	13.88 Volt	20 Pkt	88
1786723705	37.5 C	13.88 Volt	20 Pkt	88
1786723105	37.5 C	13.88 Volt	20 Pkt	88
1786722505	37.5 C	13.88 Volt	20 Pkt	89
1786721906	37.5 C	13.88 Volt	20 Pkt	89
1786721905	37.5 C	13.88 Volt	20 Pkt	89
1786721305	37.5 C	13.88 Volt	20 Pkt	89
1786720705	37.5 C	13.88 Volt	20 Pkt	92

*Used Equation Coefficients:

Temp: 0, 0.5, -64

Vin: 0, 0.075, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Value5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)