APRS Track Direct

My position About ☰

reset

BG6STS-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BG6STS-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	Sate*	Temp*	Pa*	Volt*
1762308707	9	31.3 C	1008 hPa	11.96 V
1762308656	10	31.2 C	1009 hPa	11.9 V
1762308501	8	31 C	1009 hPa	11.96 V
1762308448	9	31 C	1009 hPa	11.96 V
1762308397	9	30.8 C	1009 hPa	11.9 V
1762308142	10	30.5 C	1009 hPa	11.96 V
1762308090	8	30.6 C	1009 hPa	13.58 V
1762308041	8	30.6 C	1009 hPa	11.88 V
1762307989	8	30.7 C	1010 hPa	11.93 V
1762307886	9	30.9 C	1010 hPa	11.82 V
1762307835	9	31 C	1010 hPa	13.64 V
1762307783	9	31.2 C	1010 hPa	11.93 V
1762307732	8	31.3 C	1011 hPa	11.88 V
1762307681	7	31.4 C	1011 hPa	12.45 V
1762307579	8	31.4 C	1011 hPa	13.47 V
1762307528	8	31.1 C	1011 hPa	13.47 V
1762304860	9	23.5 C	1011 hPa	11.93 V
1762304808	9	23.1 C	1011 hPa	11.9 V
1762304758	9	22.9 C	1011 hPa	11.9 V
1762304605	9	22.1 C	1011 hPa	11.9 V
1762304503	9	21.4 C	1010 hPa	11.9 V
1762304452	8	21.2 C	1010 hPa	11.9 V
1762304350	8	20.5 C	1010 hPa	11.88 V
1762304298	9	20.4 C	1010 hPa	11.85 V
1762304247	9	20.1 C	1010 hPa	11.88 V

*Used Equation Coefficients:

Sate: 0, 1, 0

Temp: 0, 0.1, -50

Pa: 0, 1, 0

Volt: 0, 0.01, 0

--: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)