APRS Track Direct

My position About ☰

reset

KC0LFQ-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KC0LFQ-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

Time	Battery*	Temp*
1778019703	10.55 Volts	19.76 Deg.C
1778019096	10.55 Volts	19.76 Deg.C
1778018477	10.58 Volts	19.27 Deg.C
1778017874	10.58 Volts	19.27 Deg.C
1778017273	10.55 Volts	19.27 Deg.C
1778016670	10.58 Volts	19.27 Deg.C
1778014863	10.55 Volts	19.27 Deg.C
1778011795	10.58 Volts	17.32 Deg.C
1778011185	10.58 Volts	17.32 Deg.C
1778010579	10.61 Volts	17.32 Deg.C
1778009980	10.61 Volts	17.81 Deg.C
1778008144	10.64 Volts	17.81 Deg.C
1778007539	10.61 Volts	17.81 Deg.C
1778006935	10.61 Volts	17.81 Deg.C
1778006301	10.64 Volts	17.32 Deg.C
1778005065	10.64 Volts	15.85 Deg.C
1778004460	10.64 Volts	15.36 Deg.C
1778003854	10.64 Volts	15.36 Deg.C
1778002040	10.64 Volts	13.89 Deg.C
1778001431	10.67 Volts	13.4 Deg.C
1778000824	10.69 Volts	13.4 Deg.C
1778000202	10.69 Volts	12.92 Deg.C
1777999593	10.69 Volts	13.4 Deg.C
1777998988	10.69 Volts	13.4 Deg.C

*Used Equation Coefficients:

Battery: 0, 0.0293, 0

Temp: 0, 0.489, -273.15

Value3: 0, 1, 0

Value4: 0, 1, 0

Value5: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)