APRS Track Direct

My position About ☰

reset

9W2YIE-2 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 9W2YIE-2. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	RxTraffic*	RSSI*	Voltage*
1786744715	0 Pkt	-41 dBm	0.12 V
1786744676	6442 Pkt	0 dBm	0 V
1786743694	0 Pkt	-41 dBm	0.12 V
1786742673	0 Pkt	31 dBm	0.12 V
1786742633	6442 Pkt	0 dBm	0 V
1786741651	0 Pkt	-40 dBm	0.12 V
1786741612	6442 Pkt	0 dBm	0 V
1786740631	0 Pkt	-39 dBm	0.12 V
1786740591	6442 Pkt	0 dBm	0 V
1786739609	0 Pkt	-42 dBm	0.12 V
1786737526	6442 Pkt	0 dBm	0 V
1786736544	0 Pkt	31 dBm	0.12 V
1786736504	6442 Pkt	0 dBm	0 V
1786735522	0 Pkt	-42 dBm	0.12 V
1786735483	6442 Pkt	0 dBm	0 V
1786734501	0 Pkt	-42 dBm	0.12 V
1786734460	6442 Pkt	0 dBm	0 V
1786733478	0 Pkt	-42 dBm	0.12 V
1786733439	6442 Pkt	0 dBm	0 V
1786732457	0 Pkt	31 dBm	0.12 V
1786729352	6442 Pkt	0 dBm	0 V
1786728370	0 Pkt	-42 dBm	0.12 V
1786728331	6442 Pkt	0 dBm	0 V
1786727349	0 Pkt	31 dBm	0.12 V
1786727311	6442 Pkt	0 dBm	0 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)