APRS Track Direct

My position About ☰

reset

FW0978 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object FW0978. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1792035207	0 Pkt	-26 dBm	0.86 V
1792034285	0 Pkt	-34 dBm	0.66 V
1792033364	0 Pkt	-32 dBm	0.84 V
1792032442	0 Pkt	-33 dBm	0.84 V
1792031492	1 Pkt	-33 dBm	0.82 V
1792030593	0 Pkt	-32 dBm	0.84 V
1792029610	0 Pkt	-33 dBm	0.92 V
1792028660	0 Pkt	-32 dBm	0.86 V
1792027710	0 Pkt	-33 dBm	0.92 V
1792026760	0 Pkt	-32 dBm	0.98 V
1792025821	0 Pkt	-33 dBm	0.86 V
1792024883	0 Pkt	-32 dBm	1 V
1792023961	0 Pkt	-32 dBm	1 V
1792023035	0 Pkt	-31 dBm	0.94 V
1792022319	0 Pkt	-31 dBm	1.07 V
1792021053	0 Pkt	-31 dBm	1.05 V
1792020141	0 Pkt	-31 dBm	1.03 V
1792019182	0 Pkt	-32 dBm	1.03 V
1792018233	0 Pkt	-33 dBm	1.07 V
1792017497	0 Pkt	-32 dBm	1.15 V
1792016253	0 Pkt	-35 dBm	1.07 V
1792015297	0 Pkt	-33 dBm	1.17 V
1792014378	0 Pkt	-32 dBm	1.56 V
1792013425	0 Pkt	-32 dBm	1.15 V
1792012502	0 Pkt	-33 dBm	1.54 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)