APRS Track Direct

My position About ☰

reset

KI0AU-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KI0AU-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Tbatt*	Rx1h*	Dg1h*
1790699570	23.5 C	90 Pkt	20 Pkt
1790698370	23.5 C	120 Pkt	40 Pkt
1790695967	23 C	150 Pkt	50 Pkt
1790693564	22.5 C	260 Pkt	50 Pkt
1790692363	22 C	340 Pkt	80 Pkt
1790691162	22 C	400 Pkt	100 Pkt
1790689961	22 C	450 Pkt	110 Pkt
1790688760	21.5 C	470 Pkt	100 Pkt
1790687559	21.5 C	510 Pkt	120 Pkt
1790686358	21.5 C	540 Pkt	120 Pkt
1790685157	21.5 C	510 Pkt	120 Pkt
1790683955	22 C	490 Pkt	110 Pkt
1790682754	22 C	450 Pkt	110 Pkt
1790681555	22 C	480 Pkt	120 Pkt
1790680354	22 C	500 Pkt	130 Pkt
1790679151	22 C	560 Pkt	140 Pkt
1790677950	22 C	590 Pkt	150 Pkt
1790676750	22 C	620 Pkt	170 Pkt
1790675548	22.5 C	620 Pkt	180 Pkt
1790674347	22.5 C	600 Pkt	180 Pkt
1790673148	22.5 C	550 Pkt	160 Pkt
1790671944	22.5 C	530 Pkt	150 Pkt
1790670743	22.5 C	530 Pkt	160 Pkt
1790669543	23 C	540 Pkt	170 Pkt
1790668341	23 C	520 Pkt	160 Pkt

*Used Equation Coefficients:

Tbatt: 0, 0.5, -64

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

InVolt: 0, 0, 0

Vbatt: 0, 0.1377, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)