APRS Track Direct

My position About ☰

reset

OE3OMK Telemetry

This is the latest recevied telemetry packets stored in our database for station/object OE3OMK. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vmains*	Fmains*	Vdc*	Adc*	Wtotal*
1790647698	230 V	49.9 Hz	13.7 V	1.4 A	19 W
1790647217	239 V	49.9 Hz	13.6 V	1.4 A	19 W
1790646738	231 V	50 Hz	13.7 V	1.3 A	18 W
1790646256	236 V	49.9 Hz	13.6 V	1.4 A	19 W
1790645776	232 V	49.9 Hz	13.7 V	1.4 A	19 W
1790645299	237 V	50 Hz	13.7 V	1.4 A	19 W
1790644816	239 V	49.9 Hz	13.7 V	1.4 A	19 W
1790643858	230 V	49.9 Hz	13.7 V	1.3 A	18 W
1790643378	231 V	50 Hz	13.7 V	1.4 A	19 W
1790642897	240 V	49.9 Hz	13.7 V	1.4 A	19 W
1790642417	239 V	50 Hz	13.7 V	1.4 A	19 W
1790641457	238 V	49.9 Hz	13.7 V	1.4 A	19 W
1790640977	235 V	49.9 Hz	13.7 V	1.4 A	19 W
1790640497	234 V	49.9 Hz	13.7 V	1.4 A	19 W
1790640018	238 V	49.9 Hz	13.7 V	1.3 A	18 W
1790639537	238 V	49.9 Hz	13.7 V	1.4 A	19 W
1790639057	239 V	50 Hz	13.7 V	1.4 A	19 W
1790638583	239 V	49.9 Hz	13.7 V	1.4 A	19 W
1790638097	235 V	50 Hz	13.7 V	1.3 A	18 W
1790637616	239 V	49.9 Hz	13.7 V	1.4 A	19 W
1790637137	231 V	50 Hz	13.6 V	7.1 A	97 W
1790636656	237 V	49.9 Hz	13.7 V	1.4 A	19 W
1790636178	234 V	49.9 Hz	13.7 V	1.4 A	19 W
1790635698	231 V	49.9 Hz	13.7 V	1.4 A	19 W
1790635218	242 V	50 Hz	13.7 V	1.4 A	19 W

*Used Equation Coefficients:

Vmains: 0, 1, 0

Fmains: 0, 1, 0

Vdc: 0, 1, 0

Adc: 0, 1, 0

Wtotal: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)