APRS Track Direct

My position About ☰

reset

BM3DQG-12 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BM3DQG-12. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	CPUTemp*	RxPkts/10m*	RxPkts/1h*	RxPkts/24h*
1758189669	63 C	80 p	329 p	1751 p
1758188469	63 C	74 p	240 p	1594 p
1758187269	63 C	32 p	191 p	1486 p
1758186069	63 C	34 p	189 p	1422 p
1758184869	64 C	34 p	171 p	1354 p
1758183668	64 C	28 p	158 p	1295 p
1758182469	64 C	32 p	147 p	1233 p
1758181268	64 C	20 p	134 p	1183 p
1758180068	64 C	31 p	132 p	1137 p
1758178868	63 C	20 p	116 p	1086 p
1758177669	63 C	24 p	117 p	1049 p
1758176469	63 C	18 p	119 p	1005 p
1758175269	63 C	19 p	145 p	970 p
1758174069	63 C	18 p	149 p	932 p
1758172869	63 C	31 p	158 p	886 p
1758171669	63 C	19 p	145 p	825 p
1758170468	63 C	24 p	140 p	783 p
1758169268	63 C	25 p	111 p	728 p
1758168068	62 C	21 p	106 p	680 p
1758166868	63 C	13 p	125 p	643 p
1758165668	63 C	17 p	135 p	617 p
1758164468	63 C	29 p	134 p	574 p
1758163268	63 C	21 p	138 p	518 p
1758162068	62 C	19 p	149 p	482 p
1758160868	62 C	36 p	162 p	440 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/10m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)