APRS Track Direct

My position About ☰

reset

SK3JR-4 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SK3JR-4. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Vin*	Bat*	Wind*	Temp*
1790661429	13.13 Volt	12.9 Volt	3.3 m/s	5 C
1790660229	13.13 Volt	12.9 Volt	3.3 m/s	4.5 C
1790659029	13.13 Volt	12.9 Volt	3.6 m/s	4.5 C
1790657829	13.13 Volt	12.9 Volt	3.6 m/s	4.5 C
1790656629	13.13 Volt	12.8 Volt	3.6 m/s	5 C
1790655429	13.13 Volt	12.8 Volt	3.6 m/s	5 C
1790654229	13.13 Volt	12.8 Volt	3.6 m/s	5.5 C
1790653030	13.13 Volt	12.8 Volt	3.6 m/s	6 C
1790651830	13.13 Volt	12.8 Volt	3.3 m/s	6 C
1790650630	13.13 Volt	12.8 Volt	3.3 m/s	6.5 C
1790649430	13.13 Volt	12.8 Volt	3.3 m/s	7 C
1790648230	13.05 Volt	12.8 Volt	3.6 m/s	6.5 C
1790647030	13.05 Volt	12.8 Volt	3.6 m/s	6.5 C
1790645830	13.05 Volt	12.8 Volt	3.3 m/s	6.5 C
1790644630	13.05 Volt	12.8 Volt	3.3 m/s	6.5 C
1790643430	13.05 Volt	12.8 Volt	3.3 m/s	7 C
1790642230	13.05 Volt	12.8 Volt	3.3 m/s	6.5 C
1790641034	13.05 Volt	12.8 Volt	3.3 m/s	5 C
1790639830	13.05 Volt	12.8 Volt	3.3 m/s	5 C
1790638630	13.05 Volt	12.8 Volt	3.3 m/s	5 C
1790637430	13.05 Volt	12.8 Volt	3.3 m/s	6 C
1790636230	13.05 Volt	12.8 Volt	3.3 m/s	7 C
1790635030	13.05 Volt	12.8 Volt	3.3 m/s	7 C
1790633830	13.05 Volt	12.8 Volt	3.6 m/s	7 C
1790632630	13.05 Volt	12.8 Volt	3.6 m/s	7 C

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Bat: 0, 0.1, 0

Wind: 0, 0.3, 0

Chg: 0, 0.1953, -24.8031

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)