APRS Track Direct

My position About ☰

reset

SR9WXJ Telemetry

This is the latest recevied telemetry packets stored in our database for station/object SR9WXJ. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Rx10min*	Digi10min*	Vbatt*
1786737908	20 Pkt	0 Pkt	13.08 V
1786737175	19 Pkt	0 Pkt	13.02 V
1786736449	20 Pkt	0 Pkt	13.14 V
1786735719	20 Pkt	0 Pkt	13.12 V
1786734989	20 Pkt	0 Pkt	13.12 V
1786734256	20 Pkt	0 Pkt	13.12 V
1786733523	20 Pkt	1 Pkt	13.1 V
1786732794	20 Pkt	1 Pkt	13.12 V
1786732064	20 Pkt	0 Pkt	13.14 V
1786731330	20 Pkt	0 Pkt	13.12 V
1786730598	20 Pkt	0 Pkt	13.1 V
1786729867	20 Pkt	0 Pkt	13.34 V
1786729137	19 Pkt	0 Pkt	13.72 V
1786728415	20 Pkt	0 Pkt	14.24 V
1786727682	20 Pkt	0 Pkt	14.14 V
1786726951	72 Pkt	0 Pkt	14.22 V
1786725658	57 Pkt	0 Pkt	14.18 V
1786725046	58 Pkt	0 Pkt	14.2 V
1786724423	57 Pkt	0 Pkt	14.22 V
1786723812	58 Pkt	0 Pkt	14.22 V
1786723189	57 Pkt	0 Pkt	14.22 V
1786722581	58 Pkt	0 Pkt	14.2 V
1786721332	57 Pkt	0 Pkt	14.24 V
1786720721	58 Pkt	0 Pkt	14.22 V
1786720098	57 Pkt	0 Pkt	14.22 V

*Used Equation Coefficients:

Rx10min: 0, 1, 0

Visc10min: 0, 1, 0

Digi10min: 0, 1, 0

Vbatt: 0, 0.02, 10

Tempre: 0, 0.5, -50

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)