APRS Track Direct

My position About ☰

reset

HS9ZQR-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object HS9ZQR-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1790675534	3 Pkt	-63 dBm	12 V
1790674611	7 Pkt	-62 dBm	12.02 V
1790673688	24 Pkt	-62 dBm	12.02 V
1790672765	4 Pkt	-63 dBm	12.02 V
1790671843	5 Pkt	-63 dBm	12 V
1790670920	13 Pkt	-63 dBm	12 V
1790669998	16 Pkt	-63 dBm	12.02 V
1790669075	14 Pkt	-63 dBm	12.02 V
1790668152	8 Pkt	-63 dBm	12 V
1790667229	4 Pkt	-63 dBm	12.02 V
1790666307	17 Pkt	-63 dBm	12.02 V
1790665384	3 Pkt	-63 dBm	12.02 V
1790664462	4 Pkt	-63 dBm	12.02 V
1790663539	28 Pkt	-63 dBm	12 V
1790662615	5 Pkt	-62 dBm	12.02 V
1790661692	2 Pkt	-62 dBm	12 V
1790660770	26 Pkt	-62 dBm	12.02 V
1790659848	3 Pkt	-62 dBm	12 V
1790658926	17 Pkt	-63 dBm	12.02 V
1790658003	8 Pkt	-63 dBm	12.02 V
1790657080	11 Pkt	-63 dBm	12.02 V
1790656157	11 Pkt	-63 dBm	12 V
1790655235	14 Pkt	-63 dBm	12 V
1790654312	19 Pkt	-62 dBm	12 V
1790653389	17 Pkt	-63 dBm	12 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)