APRS Track Direct

My position About ☰

reset

YD0RDD-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object YD0RDD-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	TxTraffic*	RSSI*	Voltage*
1778063410	0 Pkt	-32 dBm	0.14 V
1778061588	1 Pkt	-44 dBm	0.14 V
1778059766	2 Pkt	-36 dBm	0.12 V
1778057944	0 Pkt	-35 dBm	0.14 V
1778056122	6 Pkt	-41 dBm	0.14 V
1778054300	0 Pkt	-30 dBm	0.14 V
1778052478	0 Pkt	-35 dBm	0.14 V
1778050656	0 Pkt	-30 dBm	0.14 V
1778048834	1 Pkt	-32 dBm	0.14 V
1778047012	0 Pkt	-31 dBm	0.14 V
1778045190	0 Pkt	-35 dBm	0.14 V
1778043368	0 Pkt	-35 dBm	0.14 V
1778041546	0 Pkt	-31 dBm	0.14 V
1778039724	0 Pkt	-36 dBm	0.14 V
1778037902	0 Pkt	-30 dBm	0.14 V
1778036080	0 Pkt	-34 dBm	0.14 V
1778034258	0 Pkt	-33 dBm	0.14 V
1778031244	1 Pkt	-35 dBm	0.14 V
1778029422	0 Pkt	-31 dBm	0.14 V
1778026409	2 Pkt	-40 dBm	0.14 V
1778024587	1 Pkt	-33 dBm	0.14 V
1778022765	4 Pkt	-33 dBm	0.14 V
1778020942	0 Pkt	-39 dBm	0.14 V
1778019120	0 Pkt	-34 dBm	0.14 V
1778017298	0 Pkt	-37 dBm	0.14 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)