APRS Track Direct

My position About ☰

reset

W9IPA-11 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object W9IPA-11. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Vin*	Rx1h*	Dg1h*	Eff1h*
1790634117	12.75 Volt	180 Pkt	20 Pkt	79 Pcnt
1790632917	12.75 Volt	220 Pkt	30 Pkt	83 Pcnt
1790631717	12.75 Volt	270 Pkt	30 Pkt	86 Pcnt
1790630517	12.75 Volt	300 Pkt	30 Pkt	88 Pcnt
1790629317	12.75 Volt	320 Pkt	30 Pkt	87 Pcnt
1790628117	12.75 Volt	300 Pkt	20 Pkt	87 Pcnt
1790626917	12.75 Volt	270 Pkt	20 Pkt	86 Pcnt
1790625717	12.75 Volt	230 Pkt	20 Pkt	84 Pcnt
1790624517	12.75 Volt	200 Pkt	20 Pkt	74 Pcnt
1790623317	12.75 Volt	230 Pkt	30 Pkt	71 Pcnt
1790622117	12.75 Volt	260 Pkt	30 Pkt	70 Pcnt
1790620918	12.75 Volt	290 Pkt	30 Pkt	73 Pcnt
1790619718	12.75 Volt	330 Pkt	20 Pkt	69 Pcnt
1790618518	12.75 Volt	380 Pkt	20 Pkt	68 Pcnt
1790617318	12.75 Volt	490 Pkt	20 Pkt	68 Pcnt
1790616118	12.75 Volt	600 Pkt	20 Pkt	69 Pcnt
1790614918	12.75 Volt	710 Pkt	20 Pkt	67 Pcnt
1790613718	12.75 Volt	810 Pkt	30 Pkt	66 Pcnt
1790612518	12.75 Volt	850 Pkt	30 Pkt	65 Pcnt
1790611318	12.75 Volt	930 Pkt	40 Pkt	68 Pcnt
1790608918	12.75 Volt	1070 Pkt	50 Pkt	73 Pcnt
1790607718	12.75 Volt	1100 Pkt	60 Pkt	70 Pcnt
1790606518	12.75 Volt	1100 Pkt	50 Pkt	69 Pcnt
1790605319	12.75 Volt	1070 Pkt	50 Pkt	65 Pcnt
1790604119	12.75 Volt	1100 Pkt	40 Pkt	64 Pcnt

*Used Equation Coefficients:

Vin: 0, 0.075, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

A5: 0, 0, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)