APRS Track Direct

My position About ☰

reset

BV2CW-9 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BV2CW-9. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 >>

Time	CPUTemp*	RxPkts/20m*	RxPkts/1h*	RxPkts/24h*
1749315928	33.2 C	27 p	80 p	3044 p
1749314728	32.8 C	27 p	110 p	3040 p
1749313528	32.8 C	26 p	204 p	3036 p
1749312328	32.7 C	57 p	237 p	3067 p
1749311128	33.2 C	121 p	209 p	3036 p
1749309927	33.4 C	59 p	118 p	2932 p
1749308727	32.8 C	29 p	89 p	2908 p
1749307527	32.9 C	30 p	88 p	2906 p
1749306328	33.9 C	30 p	87 p	2904 p
1749305128	33.8 C	28 p	86 p	2917 p
1749303928	33.6 C	29 p	88 p	2914 p
1749302728	33.7 C	29 p	87 p	2920 p
1749301528	33.4 C	30 p	86 p	2959 p
1749300328	33.8 C	28 p	81 p	2965 p
1749299127	34.2 C	28 p	98 p	2972 p
1749297928	34.8 C	25 p	97 p	2970 p
1749296728	34.5 C	45 p	107 p	2975 p
1749295528	34.5 C	27 p	130 p	2969 p
1749294328	33.8 C	35 p	191 p	2984 p
1749293128	33.9 C	68 p	248 p	2986 p
1749291927	34.6 C	88 p	245 p	2943 p
1749290727	34.5 C	92 p	236 p	2911 p
1749289527	34.8 C	65 p	230 p	2879 p
1749288327	35.1 C	79 p	200 p	2851 p
1749287127	34.4 C	86 p	144 p	2802 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/20m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)