APRS Track Direct

My position About ☰

reset

BX6AM-7 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object BX6AM-7. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	CPUTemp*	RxPkts/10m*	RxPkts/1h*	RxPkts/24h*	DiGi*
1836274433	56 C	30 p	117 p	456 p	378 p
1782530459	47 C	6 p	35 p	131 p	228 p
1782529259	47 C	7 p	34 p	120 p	225 p
1782526858	45 C	5 p	33 p	96 p	218 p
1782525658	46 C	3 p	32 p	86 p	214 p
1782524460	45 C	7 p	30 p	76 p	211 p
1782523259	45 C	4 p	29 p	63 p	208 p
1782522058	45 C	3 p	49 p	54 p	205 p
1782520858	45 C	7 p	46 p	46 p	203 p
1782519659	45 C	7 p	34 p	34 p	200 p
1782518458	46 C	5 p	5 p	5 p	196 p
1782517259	48 C	30 p	79 p	1000 p	193 p
1782516059	47 C	10 p	50 p	955 p	190 p
1782514859	47 C	5 p	50 p	935 p	186 p
1782513659	48 C	5 p	56 p	921 p	183 p
1782512458	47 C	8 p	57 p	905 p	179 p
1782511259	47 C	10 p	70 p	885 p	176 p
1782510060	47 C	12 p	73 p	865 p	173 p
1782508859	47 C	12 p	75 p	848 p	170 p
1782507659	47 C	13 p	56 p	815 p	166 p
1782506459	47 C	11 p	48 p	792 p	163 p
1782505260	47 C	7 p	44 p	773 p	159 p
1782504059	47 C	4 p	43 p	759 p	155 p
1782502859	48 C	7 p	38 p	744 p	152 p
1782499258	48 C	7 p	38 p	706 p	142 p

*Used Equation Coefficients:

CPUTemp: 0, 1, 0

RxPkts/10m: 0, 1, 0

RxPkts/1h: 0, 1, 0

RxPkts/24h: 0, 1, 0

DiGi: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)