APRS Track Direct

My position About ☰

reset

KI0AU-1 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object KI0AU-1. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	Tbatt*	Rx1h*	Dg1h*
1745051247	15.5 C	80 Pkt	20 Pkt
1745050647	15.5 C	80 Pkt	20 Pkt
1745050647	15.5 C	80 Pkt	20 Pkt
1745050046	15.5 C	70 Pkt	20 Pkt
1745049451	15.5 C	50 Pkt	10 Pkt
1745049446	15.5 C	50 Pkt	10 Pkt
1745048845	15.5 C	50 Pkt	10 Pkt
1745048245	15.5 C	50 Pkt	10 Pkt
1745048245	15.5 C	50 Pkt	10 Pkt
1745047644	16 C	50 Pkt	10 Pkt
1745047044	16 C	40 Pkt	10 Pkt
1745047043	16 C	40 Pkt	10 Pkt
1745046443	16 C	50 Pkt	10 Pkt
1745045843	16 C	50 Pkt	10 Pkt
1745045842	16 C	50 Pkt	10 Pkt
1745045242	16 C	50 Pkt	10 Pkt
1745044642	16 C	60 Pkt	20 Pkt
1745044641	16 C	60 Pkt	20 Pkt
1745044041	16.5 C	70 Pkt	20 Pkt
1745043441	16.5 C	80 Pkt	20 Pkt
1745043440	16.5 C	80 Pkt	20 Pkt
1745042840	16.5 C	80 Pkt	20 Pkt
1745042240	16.5 C	90 Pkt	20 Pkt
1745042239	16.5 C	90 Pkt	20 Pkt
1745041638	16.5 C	100 Pkt	20 Pkt

*Used Equation Coefficients:

Tbatt: 0, 0.5, -64

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

InVolt: 0, 0, 0

Vbatt: 0, 0.1377, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)