APRS Track Direct

My position About ☰

reset

LU2EGA-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU2EGA-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1790645729	47 Pkt	-74 dBm	5.43 V
1790644472	42 Pkt	-75 dBm	5.43 V
1790643217	82 Pkt	-74 dBm	5.41 V
1790641932	62 Pkt	-75 dBm	5.43 V
1790640668	30 Pkt	-76 dBm	5.43 V
1790639422	11 Pkt	-75 dBm	5.43 V
1790638190	2 Pkt	-76 dBm	5.43 V
1790636866	2 Pkt	-73 dBm	5.43 V
1790635646	5 Pkt	-73 dBm	5.43 V
1790634415	0 Pkt	-75 dBm	5.43 V
1790633192	0 Pkt	-74 dBm	5.43 V
1790631970	7 Pkt	-75 dBm	5.43 V
1790630743	1 Pkt	-75 dBm	5.43 V
1790629519	4 Pkt	-74 dBm	5.43 V
1790628293	2 Pkt	-73 dBm	5.43 V
1790627069	1 Pkt	-74 dBm	5.43 V
1790625845	0 Pkt	-75 dBm	5.43 V
1790624622	2 Pkt	-73 dBm	5.46 V
1790623398	21 Pkt	-74 dBm	5.43 V
1790622157	12 Pkt	-74 dBm	5.43 V
1790620926	19 Pkt	-74 dBm	5.43 V
1790619691	7 Pkt	-73 dBm	5.43 V
1790618462	10 Pkt	-74 dBm	5.43 V
1790617231	5 Pkt	-74 dBm	5.43 V
1790616004	7 Pkt	-73 dBm	5.43 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)