APRS Track Direct

My position About ☰

reset

F4EXC-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object F4EXC-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	Vin*	Eff1h*	Temp*
1754670759	13.04 Volt	100 Pcnt	31 C
1754670459	13.04 Volt	100 Pcnt	30.5 C
1754670159	13.04 Volt	100 Pcnt	30.5 C
1754669859	13.04 Volt	100 Pcnt	30 C
1754669559	13.04 Volt	100 Pcnt	29.5 C
1754669259	13.04 Volt	100 Pcnt	29 C
1754668959	13.04 Volt	100 Pcnt	28.5 C
1754668659	13.04 Volt	100 Pcnt	27.5 C
1754668359	13.04 Volt	100 Pcnt	26.5 C
1754668059	13.04 Volt	100 Pcnt	25.5 C
1754664628	13.04 Volt	100 Pcnt	26 C
1754664328	13.04 Volt	100 Pcnt	26 C
1754664028	13.04 Volt	100 Pcnt	26 C
1754663728	13.04 Volt	100 Pcnt	26 C
1754663428	13.04 Volt	100 Pcnt	26 C
1754663128	13.04 Volt	100 Pcnt	26 C
1754662828	13.04 Volt	100 Pcnt	26 C
1754662528	13.04 Volt	100 Pcnt	26 C
1754662228	13.04 Volt	100 Pcnt	26 C
1754661928	13.04 Volt	100 Pcnt	26 C
1754661628	13.04 Volt	100 Pcnt	26 C
1754661328	13.04 Volt	100 Pcnt	26 C
1754661028	13.04 Volt	100 Pcnt	26 C
1754660728	13.04 Volt	100 Pcnt	26 C
1754660428	13.04 Volt	100 Pcnt	26 C

*Used Equation Coefficients:

Vin: 0, 0.079, 0

Rx1h: 0, 10, 0

Dg1h: 0, 10, 0

Eff1h: 0, 1, 0

Temp: 0, 0.5, -64

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)