APRS Track Direct

My position About ☰

reset

LU4OFA-10 Telemetry

This is the latest recevied telemetry packets stored in our database for station/object LU4OFA-10. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 4 >>

Time	TxTraffic*	RSSI*	Voltage*
1791761811	111 Pkt	-59 dBm	12.06 V
1791760797	85 Pkt	-59 dBm	12.06 V
1791759783	130 Pkt	-64 dBm	12 V
1791758762	74 Pkt	-58 dBm	12.06 V
1791757748	50 Pkt	-58 dBm	12.02 V
1791756734	62 Pkt	-59 dBm	12.06 V
1791755720	66 Pkt	-59 dBm	12.02 V
1791754705	68 Pkt	-63 dBm	12 V
1791753691	41 Pkt	-60 dBm	12.02 V
1791752677	54 Pkt	-60 dBm	11.98 V
1791751663	71 Pkt	-72 dBm	12.02 V
1791750648	63 Pkt	-59 dBm	12.06 V
1791749634	57 Pkt	-60 dBm	12 V
1791748619	31 Pkt	-59 dBm	12.02 V
1791747605	38 Pkt	-57 dBm	11.98 V
1791746591	39 Pkt	-57 dBm	12.02 V
1791745577	50 Pkt	-57 dBm	12.06 V
1791744562	54 Pkt	-56 dBm	12.02 V
1791743548	36 Pkt	-56 dBm	12 V
1791742534	51 Pkt	-54 dBm	12.02 V
1791741520	59 Pkt	-54 dBm	12.02 V
1791740506	59 Pkt	-57 dBm	12.02 V
1791739492	53 Pkt	-58 dBm	12.02 V
1791738478	68 Pkt	-54 dBm	12.06 V
1791737460	5 Pkt	-54 dBm	12.02 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)