APRS Track Direct

My position About ☰

reset

9M4GEF Telemetry

This is the latest recevied telemetry packets stored in our database for station/object 9M4GEF. If no packets are shown the sender has not sent any telemetry packets the latest 1 day(s).

Telemetry packets is used to share measurements like repeteater parameters, battery voltage, radiation readings (or any other measurements).

<< 1 2 3 >>

Time	TxTraffic*	RSSI*	Voltage*
1779756919	10 Pkt	-46 dBm	4.92 V
1779755670	14 Pkt	-46 dBm	4.92 V
1779754422	4 Pkt	-46 dBm	4.94 V
1779753303	4 Pkt	-46 dBm	4.98 V
1779751979	11 Pkt	-46 dBm	4.92 V
1779750744	5 Pkt	-46 dBm	4.96 V
1779749515	6 Pkt	-46 dBm	4.88 V
1779748278	4 Pkt	-47 dBm	4.94 V
1779747244	6 Pkt	-46 dBm	4.98 V
1779745918	5 Pkt	-46 dBm	4.94 V
1779744590	2 Pkt	-47 dBm	4.98 V
1779743366	10 Pkt	-47 dBm	4.92 V
1779742130	4 Pkt	-47 dBm	4.96 V
1779741029	0 Pkt	-47 dBm	4.88 V
1779740253	5 Pkt	-46 dBm	4.94 V
1779739115	3 Pkt	-47 dBm	4.96 V
1779737888	2 Pkt	-48 dBm	4.96 V
1779736658	6 Pkt	-50 dBm	4.98 V
1779735328	2 Pkt	-49 dBm	5 V
1779734051	0 Pkt	-48 dBm	4.94 V
1779732697	6 Pkt	-48 dBm	4.94 V
1779731652	5 Pkt	-49 dBm	4.98 V
1779730227	1 Pkt	-48 dBm	4.98 V
1779728999	3 Pkt	-49 dBm	4.94 V
1779727869	5 Pkt	-48 dBm	4.96 V

*Used Equation Coefficients:

RxTraffic: 0, 1, 0

TxTraffic: 0, 1, 0

RxDrop: 0, 1, 0

RSSI: 0, -1, 0

Voltage: 0, 1, 0

The parameter names for the analog channels will be Value1, Value2, Value3 (up to Value5) if station has not sent a PARAM-packet that specifies the parameter names for each analog channel.
Each analog value is a decimal number between 000 and 255 (according to APRS specifications). The receiver use the telemetry equation coefficientsto to restore the original sensor values. If no EQNS-packet with equation coefficients is sent we will show the values as is (this corresponds to the equation coefficients a=0, b=1 and c=0).
The sent equation coefficients is used in the equation: a * value² + b * value + c.
The units for the analog values will not be shown if station has not sent a UNIT-packet specifying what unit's to use.
The parameter names for the digital bits will be Bit1, Bit2, Bit3 (up to Bit8) if station has not sent a PARAM-packet that specifies the parameter names for each digital bit.
All bit labels will be named "On" if station has not sent a UNIT-packet that specifies the label of each bit.
A bit is considered to be On when the bit is 1 if station has not sent a BITS-packet that specifies another "Bit sense" (a BITS-packet specify the state of the bits that match the BIT labels)